Vial filling and capping machine

Fabtech supplies vial filling and capping machines for parenteral and sterile liquids. Fabtech also supplies vial and ampoule filling lines and prefilled syringe (PFS) lines.

Parenteral medicines are given by injection or infusion. The machines fill from 1,500 to 6,500 vials an hour. The machine fills, stoppers and caps each vial in one pass. You can install it as a stand-alone unit, or integrate it with upstream and downstream equipment on a complete line.

We reply within 24 hours.

Key fact Detail

Filling lines Fabtech supplies
Vial, ampoule and prefilled syringe (PFS) lines
Installation
Stand-alone or integrated in a line
Infeed
Manual, semi-automatic or fully automatic
Dosing
Rotating piston pumps, in CIP and SIP execution
Filling zone
Fixed or movable laminar flow

The vial filling machine we supply

Fabtech's machine fills, stoppers and caps each vial in one pass, with rotating piston pumps in CIP and SIP execution.

A vial filling machine puts a measured volume of sterile liquid into a vial, seats a stopper in the neck, and crimps a cap over it. To crimp means to press the cap tight around the neck of the vial.

These three steps decide the two things a parenteral product is judged on. First, every vial must hold the dose on the label.

Second, the vial must stay closed and sterile until it is used.

Fabtech's vial filling and capping machines can be installed as a stand-alone unit or integrated with upstream and downstream equipment. The slim and compact modular design and construction has space-saving benefits.

This matters in a Grade A or B room, the cleanest room grades for sterile filling. There, every square metre is expensive to build and to run.

Output and configuration

Output depends on the number of dosing pumps. The machine takes up to five.

PumpsOutput
2 pumps1,500 vials an hour
5 pumpsup to 6,500 vials an hour

It can be integrated with various filling systems. The infeed is the part that feeds empty vials into the machine.

It can be manual, semi-automatic or fully automatic. Choose it for the batch size and the room it runs in.

The highest output figure should not decide it.

Standard execution includes manual positioning of the trays, automatic extraction positioning of the star wheel, dosage adjustment, and a manual discharge tray. On a fully automatic line, the trays and the discharge pass automatically between the machine and the rest of the line.

Nobody moves them by hand.

Specifications

  • Ceramic dosing syringes, rotating piston type.
  • Stainless steel dosing syringes, rotating piston type.
  • Dosing pumps, rotating piston type, in CIP and SIP execution.
  • Nitrogen immission during filling.
  • Fixed or movable laminar flow.
  • All safety interlocking and sensors as per GMP and FDA requirement.
  • CE compliant.

Dosing: which system for which product

The dosing system is the most important choice. You choose it to suit the product. The machine does not decide it.

Ceramic syringes hold a tighter tolerance and resist wear. A tighter tolerance means the dose varies less from vial to vial.

So ceramic suits a long production run, and a product where fill-weight variation is the critical parameter.

Stainless steel syringes suit products that do not work well with ceramic. They are also the more flexible option on a multi-product line, which is a line that fills several different products.

Both types use a rotating piston. Between strokes, the piston turns to switch its port between the inlet and the outlet.

Then it strokes to draw in the liquid and to deliver it. So the volume is fixed mechanically.

The machine does not time a flow of liquid to set it.

CIP and SIP execution means clean-in-place and sterilise-in-place. The pumps are cleaned and steam-sterilised where they stand, so nobody has to take them apart between batches.

On a sterile line, this is more than a convenience. Each time the pumps are taken apart, contamination can get in.

The team must then run validation work to prove that it did not.

Nitrogen immission means the machine puts nitrogen into the vial during filling. The nitrogen pushes the oxygen out of the headspace, the space above the liquid, before the stopper goes on.

It is used for products that oxidise, which means oxygen damages them. It is specified for each product, and it changes the machine.

The room and the line around it

A vial filling machine is qualified together with the environment it runs in, not on its own.

Filling is an open operation. Between the dose and the stopper, the product is open to the room for a short moment.

Laminar flow

Fixed or movable laminar flow over the filling zone protects the product. Laminar flow is a steady stream of filtered air that moves in one direction.

The machine is built to accept either type.

Aseptic filling means filling a sterile product without letting germs in. Our guide to aseptic filling explains this method, and the whole line is designed around it.

If the product goes into a syringe instead of a vial, the prefilled syringe machine is the equivalent unit. For the whole plant around the line, see sterile facility design and construction.

How it is specified, built and qualified

Fabtech supplies the machine to a User Requirement Specification and hands it over with a qualification file.

The User Requirement Specification (URS) is your written list of what the machine must do.

  • The work starts with the URS and the design qualification.

  • Next comes a factory acceptance test, before the machine is shipped.

  • Then come site acceptance and installation, operation and performance qualification, at your site.

Our equipment qualification page explains the full sequence. It also explains what triggers a requalification later.

Buyers who search for vial filling machine manufacturers are looking for one company that takes responsibility for the machine. Fabtech supplies the machine and stays responsible for it.

So the machine that arrives is the machine that was specified. In some projects, the vial line is one part of a whole facility.

It is not always bought on its own. In that case, a turnkey pharmaceutical project covers the process, the water, the air and the rooms together.

You can see the rest of the range on process equipment for pharma.

FAQ

What is a vial filling and capping machine?

It is a machine that puts a measured volume of sterile liquid into a vial, seats a stopper and crimps a cap over it, in one pass. It decides two things. Every vial must hold the dose on the label. The vial must stay closed and sterile until it is used.

What output can a vial filling machine reach?

Output depends on the number of dosing pumps. Fabtech's machine takes up to five. The current datasheet gives 1,500 vials an hour with two pumps and up to 6,500 an hour with five.

What dosing systems are available?

Ceramic and stainless steel dosing syringes, both rotating piston type. Also rotating piston dosing pumps in CIP and SIP execution. The product decides the choice. The machine does not. Ceramic is generally chosen for tighter tolerance over a long run. Stainless steel is chosen for flexibility on a multi-product line.

Can the machine be integrated with an existing line?

Yes. Fabtech supplies vial and ampoule filling lines and prefilled syringe (PFS) lines. You can install the machine as a stand-alone unit or integrate it with upstream and downstream equipment. The infeed can be manual, semi-automatic or fully automatic. The modular design is compact, which matters in a classified room.

How is the filling zone protected?

Fixed or movable laminar flow covers the open filling operation. Where the containment requirement is higher, the same function is built into a filling isolator line instead.

What is nitrogen immission and when is it needed?

Nitrogen pushes the oxygen out of the vial headspace before the stopper goes on. It is used for products that oxidise. It is specified for each product and it changes the machine. So it belongs in the User Requirement Specification from the start. It should not be added later.

Is the machine qualified?

Fabtech supplies it to a User Requirement Specification and hands it over with a qualification file. The steps are design qualification, a factory acceptance test before shipment, then site acceptance, installation, operation and performance qualification on site. Safety interlocking and sensors are designed to meet GMP and FDA requirements. It is built to CE requirements.

Ready to specify yours? Send your vial size, fill volume and target output

We reply within 24 hours.